{"product_id":"speedway-fabricated-ford-9-inch-rearend-axle-ho1100using-kit-60-in-width","title":"Speedway Fabricated Ford 9 Inch Rearend Axle Ho1100using Kit, 60 In. Width","description":"\n\t\t\t\t\t\u003cdiv class=\"wc-tab-inner\"\u003e\n\t\t\t\t\t\t\t\t\t\t\t\t\t\n\n\u003cp\u003eDesigned with the Builder in Mind\u003cbr\u003e\nThis housing is pumpkin-centered with uniform-length axle tubes, side-to-side. So mounting suspension brackets, especially on triangulated 3-link and 4-link systems, is much easier. Unlike factory stamped housings, these fabricated plate-steel center sections provide a wide, flat surface for easy bracket attachment. Note that the pumpkin-centered design will offset the pinion yoke about 1″ to the passenger side.\u003c\/p\u003e\n\u003cp\u003eAxle tubes are 3” O.D. with a 3\/16” wall thickness. Heavy-wall tubes, along with a larger center section, significantly reduce distortion during welding of rear-link brackets or spring pads. Billet steel “New Big Ford” (Torino) style bearing ends are fixture-welded (3.150” O.D. bearing, with 2.50” axle flange offset).\u003c\/p\u003e\n\u003cp\u003eImproved Design for Greater Durability\u003cbr\u003e\nIn addition to the heavy-duty bearing ends, the axle tubes are supported with bracing inside the large center housing. This reduces flex in the rear end housing, which is something you won’t find on stamped factory 9 inch housings. Plus, gears stay well-lubed and run cooler thanks to a large-capacity fabricated center (holds more gear oil than stamped housings). Axle is vented on the driver’s side.\u003c\/p\u003e\n\u003cp\u003eYet, with improved durability, our fabricated axle housing is on average 2 pounds lighter than stock style housings of the same size! Add your choice of axle shafts and third member (sold separately), and you are ready to roll. Equip your race car, hot rod or 4X4 with Ford 9 inch parts from Speedway Motors to ensure there are no weak links in your driveline combination.\u003c\/p\u003e\n\u003cp\u003eTotal wheel-to-wheel mounting surface width is 60″ (from hub-to-hub). The pumpkin is centered in the housing, which puts the pinion 1″ offset from center, requiring different length axle shafts. This 60″ housing includes one 30-5\/8″ long axle and one 28-1\/4″ long axle. This housing includes (8) T-bolts for the axle bearing retainer plates and (10) studs for the third member.\u003c\/p\u003e\n\u003cp\u003eForged Steel Axles\u003cbr\u003e\nOur improved axle housings deserve equally strong axles to drive your street machine. Two custom cut Currie axles made of heat-treated 1541 forged alloy steel have the strength to handle the horsepower. Axles are 31-spline, include axle shafts, axle bearings, axle seals, and bearing retainers. Flanges are dual-drilled for both 5 on 4-1\/2″ Ford\/Mopar and 5 on 4-3\/4″ GM wheel bolt patterns, and include two sizes of wheel studs (1\/2″-20 Ford\/Mopar and 7\/16″-20 GM).\u003c\/p\u003e\n\u003cp\u003eFabricated steel center section\u003cbr\u003e\n3″ O.D. axle tubes with 3\/16″ wall thickness\u003cbr\u003e\nAxle tubes are internally reinforced for additional strength, less flex\u003cbr\u003e\nBillet steel “New Big Ford” (Torino) style bearing ends\u003cbr\u003e\nForged 1541 Steel axle, dual drilled for both 5 on 4-1\/2″ Ford\/Mopar and 5 on 4-3\/4″ GM wheel bolt patterns.\u003cbr\u003e\nAccepts brake kits for 2.50″ axle shaft flange offset (from housing flange)\u003cbr\u003e\nHousing measures 55″ from flange-to-flange\u003cbr\u003e\nAssembled rearend measures 60″ from hub-to-hub (axle flange face-to-face)\u003cbr\u003e\nIncludes one 30-5\/8″ long axle and one 28-1\/4″ long axle\u003cbr\u003e\nImproved housing design weighs approximately 2 lbs less than stock-style fabricated housings\u003cbr\u003e\nCentered pumpkin w\/ 1″ offset pinion yoke for easy suspension mock-up\u003cbr\u003e\nGreater-than-stock capacity center section holds more gear oil and runs cooler\u003cbr\u003e\nRequires different length axle shafts, left\/right\u003cbr\u003e\nIncludes vent on driver side axle tube\u003cbr\u003e\nIncludes studs for 3rd member and 3\/8” T-bolts for bearing retainer plates\u003cbr\u003e\n3rd Member retainer stud nuts and washers not included but available separately as # 919-0916 (see related components at right)\u003cbr\u003e\n3rd member sold separately\u003c\/p\u003e\n\t\t\t\t\t\t\t\t\t\t\t\u003c\/div\u003e\n\t\t\t\t","brand":"X MotorSteelParts","offers":[{"title":"Default Title","offer_id":67524874207522,"sku":null,"price":2000.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1023\/5750\/0194\/files\/photo_2023-11-29_03-44-23.jpg?v=1791987338","url":"https:\/\/xmotorparts.store\/products\/speedway-fabricated-ford-9-inch-rearend-axle-ho1100using-kit-60-in-width","provider":"X MotorParts","version":"1.0","type":"link"}